- 您现在的位置：买卖IC网 > Sheet目录336 > LDS8620-002-T2 (IXYS)IC LED DRIVER FLASH 16WQFN
LDS8620
PIN DESCRIPTION
Pin #
1
2
3
4-6
7
8
9
10
11
12
13 - 15
Name
NC
LEDA
LEDB
NC
V OUT
V IN
C1+
C1-
C2+
C2-
GND
Function
No connect
LED A cathode terminal
LED B cathode terminal
No connect
Charge pump output connected to the LED anodes
Charge pump input, connect to battery or supply
Bucket capacitor 1 Positive terminal
Bucket capacitor 1 Negative terminal
Bucket capacitor 2 Positive terminal
Bucket capacitor 2 Negative terminal
Ground Reference, Connect all these pins to GND
16
PAD
EN/SET
PAD
Device enable (active high) and LED Current
Dimming Control
Connect to GND on the PCB
Top view: TQFN 16-lead 3 X 3 mm
PIN FUNCTION
V IN is the supply pin for the charge pump. A small 1 μ F
ceramic bypass capacitor is required between the Vin
pin and ground near the device. The operating input
voltage range is from 2.7V to 5.5V. Whenever the
input supply falls below the under-voltage threshold
(2.1 V), all the LED channels are disabled and the
device enters shutdown mode.
EN/SET is the enable and one wire addressable
control logic input for all LED channels. Guaranteed
levels of logic high and logic low are set at 1.3 V and
0.4 V respectively. When EN/SET is initially taken
high, the device becomes enabled and all LED
currents remain at 0 mA. To place the device into
zero current mode, the EN/SET pin must be held low
for more than 1.5 ms.
V OUT is the charge pump output that is connected to
the LED anodes. A small 1 μ F ceramic bypass
capacitor is required between the Vout pin and
ground near the device.
GND is the ground reference for the charge pump.
The pin must be connected to the ground plane on
the PCB.
C1+, C1- are connected to each side of the ceramic
bucket capacitor C1
C2+, C2- are connected to each side of the ceramic
bucket capacitor C2
LEDA and LEDB provide the internal regulated
current source for each of the LED cathodes. These
pins enter high-impedance zero current state
whenever the device is in shutdown mode.
PAD is the exposed pad underneath the package.
For best thermal performance, the pad should be
soldered to the PCB and connected to the ground
plane
? 2009 IXYS Corp.
Characteristics subject to change without notice
6
Doc. No. 8620DS, Rev. N1.1
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LDS8621002-T2-960
IC LED DRIVER FLASH 16WQFN
LDS8680008-T2
IC LED DRIVER PHOTO FLASH 16WQFN
LDS8681008-T2
IC LED DRIVER PHOTO FLASH 16WQFN
LDS8711
IC LED DRIVER PWM 32MA 8TDFN
LDS8720
IC LED DRIVER PWM 25MA 8TDFN
LDS8724
IC LED DRIVER PWM 25MA 8TDFN
LDS8726
IC LED DRIVER PWM 25MA 8TDFN
LDS8845-002-T2
IC LED DVR WHT/CLR BCKLGT 16WQFN
相关代理商/技术参数
LDS8621-002-T2
功能描述:LED照明驱动器 200mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8621002-T2-960
功能描述:IC LED DRIVER FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8640-002-T3
功能描述:LED照明驱动器 400mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8640-008-T2
功能描述:IC LED DRIVER 200MA 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8641-002-T4
功能描述:LED照明驱动器 400mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8641-008-T2
功能描述:IC LED DRIVER 200MA 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LDS8680-002-T5
功能描述:LED照明驱动器 800mA Dual Output Flash/Lamp Drvr
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS8680008-T2
功能描述:IC LED DRIVER PHOTO FLASH 16WQFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:PowerLite™ 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C